Quick answer
Our gate repair service fixes sagging, dragging and broken metal gates on-site, usually in one visit. We re-weld cracked frames, replace worn hinges, add diagonal bracing, straighten or reset posts and install new latches. When a gate is past saving, we build a new driveway, walk-through or ranch gate sized for the opening.
Key points
Most gate repairs are welded in place without taking the gate down
Sag is fixed at the cause: hinges, frame bracing or a leaning post
New gates built in steel or aluminum to match your fence
Frames reinforced and prepped when you add an automatic opener
Self-latching hardware available for pool and pet gates
Why do metal gates sag, drag or stop latching?
A gate is a lever. All of its weight hangs off one side, pulling the top hinge away from the post and pushing the bottom hinge into it. Over time something gives, and the latch end drops. Before quoting any gate repair, we figure out which part gave, because welding the wrong spot only buys a few months.
Here are the causes we see most often on residential driveway and walk gates:
Worn or undersized hinges, often bolt-on strap hinges on a heavy gate
A cracked weld where the frame meets the hinge stile
No diagonal brace, so the frame racks into a parallelogram
A hinge post leaning because the footing is shallow or the soil shifted
Rust that has thinned the bottom rail or the post at ground level
A latch that was never aligned after the gate settled
Repairing a gate in place versus taking it down
Most gates can be repaired where they hang. We support the latch end on jacks or blocks to take weight off the hinges, lift the gate back to level, then weld new hinge barrels, brace the frame or reinforce cracked corners. Working in place keeps alignment true to your actual posts, which matters more than a perfectly square gate on a shop table.
Taking a gate down makes sense when the whole bottom rail needs replacing, when the frame is badly twisted, or when the gate is going to a powder coater after the repair. Large rolling and double driveway gates may need two people or a lift to remove safely, and we will plan for that in the quote.
Either way, we protect the driveway, plants and nearby paint from sparks and grinding dust, and we test the swing several times before we pack up.
Hinges, latches and hardware we install
Hardware is where many gates fail first. A heavy steel driveway gate on light strap hinges will sag no matter how good the frame welds are. We size hinges to the weight and width of the gate and weld them to solid metal, not to a rusted skin.
Weld-on barrel hinges and heavy-duty bearing hinges for wide or heavy gates
Adjustable hinges that let you correct small sag later with a wrench
Gravity latches, drop rods and cane bolts for double driveway gates
Self-closing hinges and magnetic or self-latching latches for pool areas
Lockable latch boxes and padlock tabs for side yards and alley gates
Gate stops and wheel kits for long gates that drag on slopes
Building a new driveway or walk gate
When a gate is rusted through, badly bent or simply the wrong size, a new one is often the better spend. We measure the opening at the top, middle and bottom, check that posts are plumb, and design the frame around the weight and the look you want. Common builds use square or rectangular steel tube for the frame, with pickets, flat bar, expanded metal, welded wire or wood infill.
For driveway gates, the frame needs to be stiff enough to carry its own weight over a long span. That usually means a heavier top rail, an internal diagonal brace that runs from the bottom hinge up to the top latch corner, and hinges rated for the load. Walk gates are lighter but still benefit from a brace if they are wider than about four feet.
If your property is mostly fence work too, our fence welding service can match the gate to existing panels so the new piece looks like it belongs.
Getting a gate ready for an automatic opener
Adding a swing or slide gate operator puts new stress on a gate. The motor pushes on one point of the frame thousands of times a year, and any flex or sag fights the opener and wears it out. We reinforce the frame, add a solid mounting plate where the operator arm attaches and make sure the gate swings freely by hand before any motor is added.
Gate operators and their safety devices are covered by a standard called UL 325, and installers typically add photo eyes or edge sensors to prevent entrapment. We handle the welding and the structural side. The opener installation and wiring is usually done by a gate operator technician or electrician, and we are happy to coordinate with whoever you choose.
How a gate repair & build job works with San Antonio Mobile Welder
01
Send photos and the opening size
A full shot of the gate, a close-up of the problem, and a rough width help us understand the job and quote it in writing.
02
Find the real cause
On-site, we check hinges, frame welds, bracing and post plumb, so the fix targets why the gate failed, not just where it shows.
03
Lift, weld and reinforce
We support the gate level, weld or replace hinges, add bracing or new rails, and reset or brace the post when it has moved.
04
Finish and test the swing
Joints are ground and primed or painted, the latch is aligned, and we swing the gate with you until it closes cleanly.
Pool gates, pet gates and safety latches
Gates that guard a pool or keep a dog in the yard have to close and latch every single time. Pool barrier rules in many areas typically call for gates that open outward from the pool, close on their own and latch automatically, with the latch release set high enough that small children cannot reach it. Exact heights and requirements vary, so always confirm with your local code official.
We weld on self-closing hinges and self-latching hardware, close up gaps at the bottom where a small dog could squeeze through, and add infill to gates with wide picket spacing. If the pool fence itself has problems, we can repair those panels during the same visit.
How much does gate repair cost?
We do not publish fixed prices because no two gates fail the same way. A cracked hinge weld on a walk gate is a quick job. A double driveway gate with a leaning post and a rusted bottom rail is a much bigger one. Your written quote spells out exactly what is included.
The main things that move the price are listed below. Sending a clear photo of the whole gate and a close-up of the problem area helps us quote accurately without an extra trip. Learn more about how we handle quotes on our about page.
Size and weight of the gate, and whether it is single or double
Whether the post or footing also needs work
New hinges, latches or operator mounts going in
How much rusted metal must be cut out and replaced
The finish: primer only, color-matched paint or prep for powder coating
Travel distance and access to the gate
Frequently asked questions
Can you fix a sagging gate without replacing it?
In most cases, yes. Sag usually comes from worn hinges, a missing diagonal brace or a leaning post. We lift the gate level, weld on heavier hinges, add a brace inside the frame or reset the post. Replacement only makes sense when rust has thinned the frame badly or the gate was built too light for its width.
My gate post is leaning. Is that a welding job?
Partly. A leaning post usually means the footing is too shallow or the soil has shifted, which welding alone will not fix. We can straighten and brace a steel post, add a diagonal kicker, or set a new post in a deeper concrete footing, then weld the gate to it. We will explain which approach fits your soil and gate weight.
How long does a typical gate repair take?
A hinge or latch repair on a walk gate is often finished within a couple of hours. A driveway gate that needs new hinges, bracing and paint can take most of a day. New custom gates take longer because we measure first, build the frame, then install, so expect a few visits spread over a week or two depending on design.
Can you weld an aluminum gate?
Yes. Aluminum gates are TIG welded, which needs very clean metal and calm air, so we set up wind screens and clean the joint thoroughly. Many aluminum gates are assembled from extrusions with screws or rivets, and those are often easier to repair with new hardware. We will tell you which approach is stronger for your gate.
Will you paint the gate after welding?
Every repair gets primer on bare steel at minimum so it does not start rusting immediately. Color-matched paint, black or bronze enamel, or cold galvanizing compound can be added in the quote. If you prefer powder coating, we can do the structural repair first and you can take the gate to a powder coater, or we can discuss timing.
Do you also repair rolling or slide gates?
Yes. Slide gates have their own wear points: bent bottom tracks, worn V-groove wheels, broken guide rollers and cracked frame welds near the wheel brackets. We replace wheels and rollers, straighten or reweld track, and reinforce the frame. If an opener is involved, we make sure the gate rolls freely by hand before the operator is reconnected.