Quick answer
Our fence welding service repairs and extends wrought iron, ornamental steel, pipe and ranch fences at your property. We replace rusted post bases, re-weld broken pickets and rails, rebuild storm or vehicle damaged sections, and weld steel posts for wood privacy fences. Repairs are primed or painted to blend with the existing fence.
Key points
Wrought iron, ornamental steel, pipe rail and ranch fence repairs
Rusted post bottoms cut out and sleeved or replaced
Damaged sections rebuilt to match existing pickets and rails
Steel posts welded and set for wood privacy fences
What kinds of fences can be welded?
Almost any steel fence can be repaired with fence welding, and many aluminum ones can too. The trick is knowing what the fence is made of before we strike an arc, because each material needs a different approach.
Solid wrought iron and older bar-stock fences, common on historic homes
Ornamental steel fences built from square tube pickets and rails
Galvanized pipe rail and ranch fences, including oilfield pipe
Welded wire and cattle panel fences on steel frames
Powder-coated aluminum fences, repaired with TIG welding or new hardware
Steel post frames that carry wood or composite privacy pickets
Rusted fence bottoms and post bases
The most common fence problem we see is rust at the bottom. Rainwater runs down pickets and posts and collects where metal meets soil, concrete or mulch. Sprinklers make it worse, and on clay-soil lots in towns like Schertz and Converse, irrigated ground stays damp against the steel for much of the year. Eventually the post rusts thin right at the ground line and the panel starts to wobble or lean, even though everything above looks fine.
The fix is to cut the post back to clean, solid metal and weld in a new section, or sleeve it with a slightly larger tube that runs below grade. For posts set in concrete, we sometimes cut off at the concrete and weld the post to a new steel base plate anchored to the slab. Bottom rails that have rusted through get replaced with new tube of the same size.
We finish by priming and painting the new metal and the area around it. Keeping mulch and soil a few inches below the bottom rail afterward helps the repair last much longer.
When a car, tree or storm takes out a section
Impact damage looks dramatic, but much of it is repairable. A bent section can sometimes be straightened with heat and pressure. When pickets are kinked or rails are torn, we cut out the damaged part and build a new section from matching tube and pickets, then weld it into the existing run so the line stays straight.
If you are filing an insurance claim, photos of the damage before we start and a written quote that lists the repair are useful. We provide the quote; you handle the claim. Posts pulled out of the ground get reset in fresh concrete before any section is welded back.
Steel posts for wood privacy fences
Wood posts rot at the ground, and when they go, the whole fence leans. Many homeowners switch to steel posts and keep their wood pickets. We set galvanized steel pipe or square tube posts in concrete and weld on brackets or flat bar tabs so the wood rails can be bolted or screwed in place.
Welded steel post frames hold up far better in wind and wet soil than wood. The galvanizing needs to be ground away where we weld, and we always coat those spots with cold galvanizing compound afterward. If the fence also needs a new gate, our gate repair and build service can add a steel-framed gate that will not sag like a wood one.
Matching old ironwork without making it look patched
Older iron fences often use picket sizes, spear tips or scroll patterns that are hard to find today. We carry common square bar sizes and can source standard castings such as spear points, finials, collars and scrolls from ornamental suppliers. When an exact match is impossible, we pick the closest profile and keep spacing identical so the eye reads the fence as one piece.
Finish matters as much as shape. A glossy black patch on a faded satin fence stands out from the street. We can match sheen as well as color, or recommend repainting the full run for a uniform look. For fences in historic districts, check with your local historic preservation office before changing materials or styles.
How a fence welding job works with San Antonio Mobile Welder
01
Walk the fence line
Send photos of each problem spot, or we walk the run with you on-site, marking every post, picket and rail that needs attention.
02
Prioritize the repairs
The written quote lists each repair separately, so you can fix safety problems first and schedule cosmetic items later if you prefer.
03
Cut, fit and weld
Rusted or damaged metal is cut back to solid steel, new material is fitted to match, and every joint is welded and ground smooth.
04
Seal and blend the finish
Bare metal is primed, galvanized spots get zinc-rich coating, and paint is matched in color and sheen to the rest of the fence.
Working with galvanized and pipe fences safely
Galvanized steel is coated in zinc, which burns off as a white fume when welded. Breathing those fumes is a known health risk, so we grind the zinc off the joint area before welding, work upwind and use proper respiratory protection. Afterward, the bare area gets a zinc-rich coating to restore rust protection.
Pipe fences on larger lots and small acreage often use thick-walled pipe that welds best with stick electrodes, especially in wind. If your fence surrounds livestock, our ranch and equipment service covers pens, panels and cattle guards too.
What affects the cost of fence welding?
Fence repair cost depends mostly on how many spots need work and how much new material goes in. Two broken pickets on one panel is a short job. Twenty rusted post bases along a long run is a full day or more. The quote lists each repair so you can decide what to do now and what can wait.
Number of posts, pickets and rail sections needing repair
Material: solid iron, steel tube, galvanized pipe or aluminum
Whether posts must be reset in new concrete
Decorative castings or custom pickets to match the original
Painting only the repairs versus refinishing the whole run
Frequently asked questions
Can you weld a wrought iron fence that is very old?
Usually, yes. True wrought iron and older mild steel both weld well once rust and old paint are cleaned off the joint. Very thin, heavily pitted pickets may be better replaced than welded. We check the metal thickness at each repair point and tell you honestly which pieces can be saved and which should be swapped for new bar.
How do you repair a fence post rusted off at the ground?
We cut the post back to solid metal and either weld in a new lower section, add a sleeve that runs into the ground or concrete, or weld the post to a new base plate anchored to the slab. The choice depends on how the post was set originally. All new metal is primed and painted to slow future rust.
Do I need to remove plants along the fence?
You do not need to remove them, but please trim back vines and shrubs a foot or two from the repair spots if you can. We use spark shields and wet down dry areas, yet clear space makes the work safer and faster. Let us know about any irrigation lines near posts that might need resetting.
Can you extend my existing iron fence?
Yes. We measure your current pickets, rails and post sizes and build new sections to match, then weld or bolt them into the existing run. Matching is easiest with common square tube styles. For fences with unusual castings, we source the closest available parts and keep spacing and height consistent so the extension looks original.
Is welding better than bolting a fence repair?
For steel and iron fences, welding is almost always stronger and looks cleaner because the repair becomes part of the original metal. Bolted repairs make sense for aluminum fences built with screws, for temporary fixes, or where heat could damage nearby finishes. We will recommend whichever method gives you the longest-lasting result.
How long does a fence repair last?
A welded repair is as strong as the surrounding metal, so it lasts as long as that metal stays protected. Keeping paint in good shape, keeping soil and mulch below the bottom rail, and aiming sprinklers away from posts all add years. Touching up chips each spring is the single best habit for any metal fence.