Home / Services / Trailer repair

Trailer repair

Mobile trailer repair without towing a broken trailer anywhere

A trailer with a cracked tongue or a sagging frame should not go down the road to a shop. We bring the welder to your driveway, barn or storage lot and make it safe to tow again.

White steel spiral staircase

Quick answer

Our mobile trailer repair service welds cracked tongues and A-frames, rusted crossmembers and frame rails, broken jack mounts, safety chain loops, ramps, gates and fenders right where the trailer is parked. We repair utility, boat, car hauler, livestock and camper trailers in steel and aluminum, and we tell you plainly when a part should be replaced instead.

Key points

Repairs done where the trailer sits, so you never tow it unsafe

Tongues, frames, crossmembers and jack mounts welded and reinforced

Aluminum boat and utility trailers TIG welded

Ramps, gates, fenders and stake pockets rebuilt

Honest advice on parts that must be replaced, not welded

Mobile trailer repair for the trailers families actually use

Most homeowners own one trailer that does a lot of work: hauling mulch, moving a kid to college, launching the boat or carrying a mower to the lake house. Those trailers take a beating, and they usually break at the worst time. Our mobile trailer repair covers the trailers families and small ranches actually use.

Single and tandem axle utility trailers with mesh or wood decks

Boat trailers in galvanized steel or aluminum

Car haulers and equipment trailers with fold-down ramps

Livestock and horse trailers, including gates and dividers

Small camper and teardrop frames

Lawn care and landscape trailers with gate ramps

Cracked tongues and A-frames: the repair that matters most

The tongue carries the whole connection between your vehicle and the load. Cracks usually start where the tongue meets the front crossmember, around the jack mount, or near the coupler where bolt holes weaken the steel. A cracked tongue can fail suddenly on a bump, which is why we treat it as a safety repair, not a cosmetic one.

We grind the crack out completely, weld it back with full penetration and then add a fish plate or gusset that spreads the load over a longer section. If the tongue is rusted thin, we replace it with new rectangular tube of the same or heavier size. The coupler is reinstalled with new grade 8 hardware and checked for proper fit on your ball.

Close-up of a metal staircase

Crossmembers, frame rails and rust-through

Crossmembers hold the deck up, and on trailers that sit in wet grass or get dunked at boat ramps, they rust from the inside out. A deck that feels soft or bows under weight often means a crossmember has cracked or rotted. Frame rails crack near spring hangers and where heavy loads concentrate over the axle.

We cut out rotted crossmembers and weld in new angle or channel, reinforce cracked rails with welded plates, and replace broken spring hanger brackets. If the deck boards are coming off anyway, that is the best time for frame work, since we can reach every joint and paint the frame fully before new boards go down.

Jacks, couplers, safety chain loops and hitch parts

Small parts fail often and are quick to fix. A swivel jack that broke off its mount, a safety chain loop that cracked loose, or a stake pocket that tore out of the side rail can all be welded the same day.

Safety chains should attach to the trailer frame with a weld or rated hardware that is at least as strong as the chain. When we weld on new chain loops, we use thick round bar or forged loops and full-length welds, not a quick tack. Your local motor vehicle department can confirm current chain and lighting requirements for your trailer class.

Weld-on and bolt-on jack mounts replaced or reinforced

Safety chain loops and hooks welded to the frame

Stake pockets and tie-down D-rings added or repaired

Spare tire carriers and toolbox mounts built to fit

Ramps, gates and fenders

Fold-down gate ramps take constant abuse. Hinges crack, springs tear out their mounts, and expanded metal mesh breaks away from the frame. We reweld hinges, add spring assist brackets, replace mesh and rebuild ramp frames from new angle or tube.

Fenders crack where they attach to the frame because they vibrate on every bump. A welded bracket with a small gusset holds far better than the original thin strap. On livestock trailers, we repair slam latches, divider gates and the bottom rails that rust from manure and moisture.

Aluminum boat and utility trailers

Aluminum trailers do not rust like steel, but they crack, especially at bunk brackets, cross bracing and the tongue. Aluminum is TIG welded, and it needs a very clean surface and calm air. We remove paint and oxide around the joint, set up wind screens and weld with filler rod matched to the alloy.

Some aluminum trailer parts are bolted extrusions that are designed to be replaced rather than welded. We will tell you which approach is stronger. For galvanized steel boat trailers, we grind off the zinc at the weld, repair the joint, then restore protection with a zinc-rich coating.

How a trailer repair job works with San Antonio Mobile Welder

01

Photos and capacity

Send photos of the damage, the whole trailer and the VIN or capacity sticker so we understand the rated load.

02

Inspect around the break

We check the metal next to the crack or rust, because welding to thin steel only moves the failure a few inches.

03

Weld, plate and replace

Cracks are ground out and welded through, reinforced with plates or gussets, and rotted members replaced with new steel.

04

Paint and safety check

Repairs are primed and painted, hardware is torqued, and we check coupler, chains and jack before you hitch up.

Parts we replace instead of welding

Being honest about limits is part of safe trailer repair. Some components are heat-treated or engineered so that welding weakens them. Cast couplers, hitch balls, torsion axle arms and bent spindles should be replaced with new rated parts. Leaf springs should never be welded.

When a trailer is badly rusted across the whole frame, repeated patching can cost more than the trailer is worth. In that case we will say so and give you options, including a frame rebuild or replacement. More on how we approach scope is on our about page.

How long does a trailer repair take?

Simple jobs like a jack mount, a chain loop or a fender bracket usually take an hour or two on-site. A cracked tongue with gusset reinforcement or two or three new crossmembers is often a half-day job. Full deck and frame rebuilds take longer and may need a second visit once new lumber is ready.

To speed things up, unload the trailer, park it on firm level ground with room to work on all sides, and send a photo of the capacity sticker. If you also need help with a ranch gate or a piece of farm equipment, we can often handle it in the same trip. Boat owners who launch at the lakes near Seguin or New Braunfels may want to read our notes on trailers that spend time in the water.

Frequently asked questions

Can you repair a trailer tongue that has cracked?

Yes, and it should be done before the trailer is towed again. We grind the crack out fully, weld it with full penetration and add a fish plate or gusset to spread the load. If the tongue is rusted thin, replacing it with new tube is the safer choice. Either way, the coupler gets reinstalled with new grade 8 hardware.

Do I need to bring my trailer to you?

No. Mobile trailer repair means we come to where the trailer is parked: your driveway, barn, pasture or storage lot. We carry our own power and steel. Please unload the trailer if possible and make sure it sits on firm, level ground with a few feet of clearance on each side so we can reach the repair.

Can you weld an aluminum boat trailer?

Yes. We TIG weld aluminum trailer brackets, cross braces and tongues after cleaning off oxide and paint. Aluminum welding needs calm air, so we use wind screens outdoors. Some aluminum trailer parts are bolted extrusions that are better replaced than welded, and we will tell you which approach makes the stronger repair.

Will welding void my trailer warranty?

Possibly. Many manufacturers limit warranty coverage if the frame is modified or repaired by someone else. If your trailer is new and still under warranty, check with the dealer or manufacturer first. For older trailers out of warranty, a properly welded and reinforced repair is the normal way to keep them safe and useful.

Can you add a spare tire mount or toolbox to my trailer?

Yes. We build and weld spare tire carriers, toolbox mounts, ladder racks, tie-down rails and extra D-rings to fit your trailer. We place them where the frame is strong enough and where they will not interfere with the jack, lights or turning clearance. Small add-ons like these are easy to bundle with a repair visit.

What trailer parts should never be welded?

Leaf springs, cast couplers, hitch balls, torsion axle arms and bent spindles should be replaced with new rated parts instead of welded. Heat changes how these parts handle stress and can make them fail without warning. We will point out any of these that look worn during our visit so you can replace them with confidence.

Get your trailer road-ready again

Send photos of the damage and the capacity sticker, and we will reply with a free written quote for a repair at your driveway. Need a gate fixed too? Our gate service fits in the same visit.

Get a Free Quote
Ornate wrought iron gate between stone pillars
San Antonio Mobile Welder logo

Mobile welding and wrought iron repair across San Antonio.

Free written quote · No obligation · Reply within one business day

San Antonio Mobile Welder

Get a free quote

Tell us what you need built or repaired. We'll reply with a clear written quote.